Maintenance Tips
Maintenance
E-Bike Display Error Codes: Solutions for Error Code E36
The display screen of Kingbull electric bicycle (e-bike) is not only an essential source of information during a ride but also shows key data such as speed, battery level, mileage, and riding mode. This information helps riders better understand the status of their bike, ensuring a smooth and safe riding experience. However, beyond these functions, the display screen has another crucial role: when a fault occurs, it can display specific error codes that inform the rider about potential issues with the e-bike.
Different error codes correspond to various types of faults, which may involve the motor, controller, braking system, or sensors, among other components. These error codes function as the e-bike’s “diagnostic tool,” helping riders quickly identify the root cause of the problem. Therefore, when an error code appears on the e-bike’s display, the rider must use the code’s meaning to conduct a thorough inspection of the bike and take appropriate measures to resolve the issue.
Kingbull Electric Bikes have received a comprehensive upgrade for 2025!
This upgrade includes a new display system, offering you more accurate riding data. To assist users with operation and troubleshooting potential screen error codes, we have prepared a detailed video guide. For instructions on the new display error code operations, please refer to the YouTube video below:
Understanding Error Code E36
Error code E36 typically indicates an issue with the electric bike's motor or that the controller has detected a voltage beyond the safe operating range. This can be caused by several factors, including:
Loose or Damaged Cables: The motor cables under the frame may be loose, broken or have poor contact, affecting power output.
Display Malfunction: The bike's display could be faulty, misinterpreting or incorrectly communicating voltage levels to the controller.
Controller Fault: The voltage detection circuit within the controller may be malfunctioning, preventing accurate transmission of voltage data, or leading to an incorrect detection of over/under-voltage conditions.
Motor Malfunction: The motor may be damaged, resulting in improper function, and might need replacement.
How to Respond to Error Code Alerts
When an error code appears on your e-bike’s display, there’s no need to panic. Most issues can be addressed through basic checks and troubleshooting. Here are some general steps to follow:
1. Check Connections and Plugs
Many fault codes stem from loose connections or damaged wires. Carefully inspect the connections of various components on your electric bike, paying special attention to the motor cables, particularly when an E36 code appears, as this is often caused by issues with the motor or motor control circuit. Check for any looseness, wear, or breakage in the motor wires, especially at the connection point under the frame.
Corrosion on Plugs: Due to moisture or dirt, plugs may corrode over time. Regularly clean the plugs and ensure they are dry.
2. Reset the Display
Sometimes, the bike’s display may need to be reset to clear temporary faults. Follow these steps to reset the display:
Enter Settings Mode: Press and hold the “+” and “-” buttons simultaneously to access the display settings menu.
Select P16 Parameter: Press the power button to navigate to the P16 parameter setting.
Reset the Display: In the P16 parameter screen, press and hold the “-” button for about five seconds to reset the display.
Save Settings: Once reset, press and hold the “+” and “-” buttons again to exit settings, then restart the display to check if the fault has been cleared.
3. Check the Controller
If the problem persists after resetting the display and inspecting the cables, it may be related to a fault in the controller. Verify that the connections between the controller and other components (like the motor and sensors) are secure and that the controller itself is functioning correctly.
For Literider models, the controller is located inside the fold of the frame. In Voyager, Rover, Hunter, and Discover models, the controller is situated near the pedals and crank. You’ll need to remove the black cover to check the controller. You can refer to these videos for guidance on how to perform this check.
4. Contact Professional Support
If you are unsure how to proceed or if the issue remains unresolved after the above steps, please contact our customer service at customers@kingbullbike.com.
To expedite the resolution of your issue, please include your order number along with any relevant images or videos of the problem. Our customer service team will respond within 48 hours with more specialized technical support.
If you encounter other fault codes E34 or E37, please click here to view the solution steps.
Conclusion
Troubleshooting E-bike error code E36 faults often involves checking connections, resetting the display, and inspecting the controller. By following these steps, common issues can be resolved. However, if problems persist, reaching out to professional support with detailed information will ensure timely assistance. Remember, regular maintenance is key to keeping your e-bike running smoothly and preventing future faults.
Read more
Maintenance
How to Replace Brake Pads
Brake pads on all electric bicycles are consumable parts that gradually wear down with long-term use. When worn to a certain extent, they can affect braking performance and even pose a safety hazard.Inspecting and replacing brake pads is crucial for every rider, as it directly impacts riding safety. This article will provide detailed guidance on the specific procedures for brake pad inspection and replacement.
Preparation for Inspection and Replacement
Brake pad replacement
Allen wrench
Needle-nose pliers
Disc brake pads wear down over time due to normal use. This can cause a slower brake response time and require more effort to press the brakes.
A squeaking noise from disc brakes is usually caused by contaminated brake pads. Even the slightest amount of oil, including from your skin, can damage disc brake pads. Minimize contact between the brake surface and bare skin whenever handling brake pads. If you do touch the pads, clean them with rubbing alcohol or a specialized product for disc brake pads. Then lightly sand the pads.
Brake Pad Inspection
Check your brake pads for shininess or visible wear. Inspect the pads by removing the wheel and examining the space where the rotor spins.
When inspecting brake pads, pay attention to the following key points:
Integrity: Ensure there are no chunks, dents, or missing parts. If there are, replace the damaged pads before your next ride.
Thickness: The pad material should be at least 1.5 mm thick. If you don't have a ruler, note that a grain of rice is about 1.5 mm thick (width, not length). If the pad is thinner than this, it’s time to replace it.
Cleanliness: The pads should be free of oil and other contaminants. If the pads are dirty, especially if they are oily (a significant safety hazard!), they need to be replaced.
Replace brake pads
Please refer to the Youtube video to install！
Read more
MaintenanceTips & Cycling Knowledge
Ultimate Guide to Silencing Your Electric Bike's Noises
Many times, we find ourselves puzzled by squeaks or unexpected noises coming from our newly assembled or regularly used electric bicycles. These noises often stem from improper assembly or wear and tear of components over time, indicating potential issues. Addressing these problems early can prevent them from worsening in the future. If your electric bike starts making noises, it’s crucial to stop and check it before continuing your ride.
Why is my electric bike making strange noises?
Identifying the source of the squeaking is crucial. Here’s how you can diagnose and fix it, as there are many parts on a bike that can produce noise. Once you pinpoint the source, refer to the relevant component below.
Brakes
The contact between the wheel and the brake pads often causes squeaks. First, check if your wheels are properly secured in the dropouts, where the wheel axles attach to the bike frame. Misalignment can cause the wheel to rub against the brake pads. Remove the wheel, tighten the quick-release skewer, and securely fix it in the dropouts.
Chain
A squeaky chain is likely dry and in need of thorough cleaning and lubrication.
Crankset
If the crankset is the source of the noise, loose bolts might be the culprit. Grab the crank arms (the parts connecting the pedals to the bike) and twist them to see if they move side to side. If they do, tighten them using the appropriately sized hex wrench.
Derailleur
Dry pulleys can often cause the derailleur to squeak. Clean them thoroughly with a dry cloth, then apply a drop of lubricant to each pulley’s axle. Also, lubricate the derailleur’s pivots by turning the pedals.
Pedals
A common question is why the bike makes noise when pedaling. The pedals themselves might be the issue. Check if they are tightened securely or if the pedal threads are damaged. If the threads are damaged and you can’t tighten the pedals, replace them promptly.
Saddle
The rails connecting the saddle to the seat post can also be a source of squeaks. Tighten the bolts securing the saddle using an appropriately sized hex wrench. If the saddle tilts and squeaks, consider taking it to a nearby bike shop.
How to Fix Squeaky Bike Brakes?
Fixing noisy brakes on an electric bike is straightforward. Follow these steps to silence your brakes
Check the Brakes
It’s easy to determine if the front or rear brakes are at fault. During a ride, test the brakes individually. If the front brake is noisy, the sound will come from the left side. If the rear brake is noisy, the sound will come from the right side. If both brakes make noise, adjust both front and rear brakes.
Clean the Rotors
If possible, use rubbing alcohol to clean the disc brake rotors and wipe them with a clean cloth or towel. Clean the brake pads with a degreaser if they are still thick; if they are thin, replace them. After cleaning the brake pads, wait for them to dry completely before reassembling.
Replace Brake Pads
Replacing the brake pads follows the same steps for both the front and rear wheels. If your bike’s brakes are squealing when applied, the brake pads are likely worn out. Worn brake pads can’t grip properly and cause squealing, reducing braking efficiency.
Summary
These solutions will help you fix the squeaking noises on your electric bike, ensuring a smoother and more enjoyable ride. Regular maintenance and timely addressing of any noises can extend the life of your bike and make your rides more pleasant. With summer around the corner, hop on your perfect KINGBULL electric bike and explore the secrets of the summer forest!
Read more